Schluter Systems Flooring

Schluter®-BEKOTEC is a modular screed system that produces permanent flooring assemblies that are free from internal stress. The BEKOTEC-EN/US/P studded polystyrene screed panels are placed directly over any loadbearing substrate and optional common sound and/ or heat-insulating layers. The studs effectively divide the screed into smaller, 4-1/4" (108 mm) square modules, thereby confining shrinkage and curing stresses to control deformations such as curling and continuous cracks that can be common in a traditional screed. These modular screed systems allow the installation of continuous screed surfaces without any control joints or wire reinforcement. The elimination of control joints allows surface movement joints to be placed to match the joint layout in the tile covering. The cross-section of the assembly reveals a minimum screed thickness of 1-1/4" (32 mm) between the studs and 5/16" (8 mm) above the studs. This results in significant material and weight savings over traditional screeds. For example, a 1-1/4" (32 mm)-thick traditional mortar bed weighs approximately 15-lb/ft2 (0.72 kPa), while a BEKOTEC mortar screed weighs approximately 12 to 12.5-lb ft2 (0.57 - 0.60 kPa), representing a 15- 20% decrease. Material and weight savings compared to a 2" (51 mm)-thick mortar bed amount to approximately 50%. LA Flooring is a certified Schluter installer, providing professional installation of the BEKOTEC system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-BEKOTEC-BRS is an edge strip for conventional screed systems at floor/wall transitions or fixed building elements. LA Flooring is a certified Schluter installer, providing professional installation of the BEKOTEC-BRS system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-BEKOTEC-BRSK is an edge strip for conventional screeds featuring an adhesive strip that allows the foam to be bonded to walls or other fixed building elements for ease of installation. LA Flooring is a certified Schluter installer, providing professional installation of the BEKOTEC-BRSK system throughout Wildwood, The Villages, and Central Florida.

Schluter®-BEKOTEC-F is a modular screed systems that produces permanent flooring assemblies that are free from internal stresses. The Schluter®-BEKOTEC-EN23F studded polystyrene screed panels that are placed directly over any load-bearing substrate and optional common sound and/or heat-insulating layers. The studs effectively divide the screed into smaller, 4-1/4" (108 mm) square modules, thereby confining shrinkage and curing stresses to control deformations such as curling and continuous cracks that can be common in a traditional screed. These modular screed systems allow the installation of continuous screed surfaces without any control joints or wire reinforcement. The elimination of control joints allows surface movement joints to be placed to match the joint layout in the tile covering. The cross-section of the assembly reveals a minimum screed thickness of 1-1/4" (32 mm) between the studs and 5/16" (8 mm) above the studs. This results in significant material and weight savings over traditional screeds. For example, a 1-1/4" (32 mm)-thick traditional mortar bed weighs approximately 15-lb/ft2 (0.72 kPa), while a BEKOTEC mortar screed weighs approximately 12 to 12.5-lb ft2 (0.57 - 0.60 kPa), representing a 15- 20% decrease. Material and weight savings compared to a 2" (51 mm)-thick mortar bed amount to approximately 50%. LA Flooring is a certified Schluter installer, providing professional installation of the BEKOTEC-F system throughout Wildwood, The Villages, and Central Florida.

Schluter®-BEKOTEC-THERM-RH 75 is a PVC clamp used to attach radiant heating tubes to the BEKOTEC-EN/US/P 1-3/8" (35 mm)-thick panels. LA Flooring is a certified Schluter installer, providing professional installation of the BEKOTEC-THERM-RH 75 system throughout Wildwood, The Villages, and Central Florida.

Schluter®-DECO is designed to provide decorative lines within tile coverings and edge protection at transitions from tile coverings to other same-height surface coverings, such as wood or carpet. It is suitable for light indoor residential floor applications only and is not intended for use in areas subject to heavy traffic, impact, or abrasive mechanical stresses (e.g., hand carts or rolling equipment). The profile is available in stainless steel, solid brass, chrome-plated solid brass, and anodized aluminum. DECO features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a 1/4" (6 mm)-wide visible surface that meets the high aesthetic requirements of showrooms, lobbies, galleries, exhibition booths, etc. The anchoring leg of DECO, in solid brass, chrome-plated solid brass, and anodized aluminum, is available with a special radius perforation “R” so that the profile can be used to form curves. DECO in chrome-plated brass requires a relatively large bending radius. LA Flooring is a certified Schluter installer, providing professional installation of the DECO system throughout Wildwood, The Villages, and Central Florida.

Schluter®-DILEX-DFP is a movement joint profile for installation at door areas or for dividing screed surfaces. LA Flooring is a certified Schluter installer, providing professional installation of the DILEX-DFP system throughout Wildwood, The Villages, and Central Florida.

Schluter®-DITRA is a polyethylene membrane with a grid structure of square cavities, each cut back in a dovetail configuration, and an anchoring fleece laminated to the underside. The anchoring fleece is embedded in thin-set mortar to provide a mechanical bond to the substrate. Tile is installed over DITRA using the thin-bed method in such a way that the mortar becomes mechanically anchored in the square, cutback cavities of the matting. Designed specifically for ceramic tile and dimension stone installations, DITRA serves as an uncoupling layer, waterproofing membrane, and vapor management layer that accommodates moisture from beneath the tile covering. Further, DITRA performs all these functions while still providing adequate support/load distribution for the tile covering. The combination of these four essential functions allows for the successful installation of tile over a wide range of substrates, including plywood/ OSB, concrete, gypsum, heated floors, etc. DITRA is 1/8" (3.5 mm) thick, which minimizes tile assembly thickness and reduces transitions to lower surface coverings (e.g., carpet, engineered wood, and vinyl). DITRA allows for ceramic tile application over single-layer plywood or OSB subfloors on joists spaced up to 19.2" (488 mm) o.c. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA & DITRA-XL system throughout Wildwood, The Villages, and Central Florida.

Schluter®-DITRA-HEAT integrates customizable, comfortable electric floor warming with the functions associated with DITRA: uncoupling, waterproofing, vapor management and support to ensure a long lasting installation. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT system throughout Wildwood, The Villages, and Central Florida.

Schluter®-DITRA-HEAT-DUO integrates customizable, comfortable electric floor warming with the functions of DITRA: uncoupling, waterproofing, vapor management and support to ensure a long lasting installation. DITRA-HEAT-DUO features an integrated thermal break to reduce heat loss to the substrate, improve floor warming response time, and reduce sound transmission through floor-ceiling assemblies. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-DUO system throughout Wildwood, The Villages, and Central Florida.

DITRA-HEAT-DUO-PS peel and stick membrane features a pressure-sensitive adhesive (PSA) to bond the membrane to the substrate, replacing the need for thin-set mortar. The peel and stick versions integrate customizable, comfortable electric floor warming with the same core functions of DITRA-HEAT: uncoupling, waterproofing, vapor management, and support to ensure a long-lasting installation. DITRA-HEAT-DUO-PS features an integrated thermal break to reduce impact sound transmission through floor-ceiling assemblies, reduce heat loss to the substrate, and improve floor warming response time. The Schluter®-DITRA-HEAT-DUO-PS membrane does not comply with the requirements specified in ANSI A118.10 – American National Standard Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation. For applications requiring membrane compliance with or certification to the ANSI A118.10, select the DITRA-HEAT-DUO membrane that is installed with thin-set mortar. Alternatively, the DITRA-HEAT-DUO-PS membrane may be covered with the Schluter(R)-KERDI membrane, which is certified to meet ANSI A118.10. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-DUO-PS system throughout Wildwood, The Villages, and Central Florida.

Schluter®-DITRA-HEAT-E-HK are twisted pair heating cables designed for integration with the DITRA-HEAT uncoupling membrane in interior floor warming applications. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-HK system throughout Wildwood, The Villages, and Central Florida.

The purpose of the Schluter®-DITRA-HEAT-E-HK-RK Repair Kit is to repair damaged Schluter®-DITRA-HEAT-E-HK heating cables to operable condition. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-HK-RK system throughout Wildwood, The Villages, and Central Florida.

The purpose of the Schluter®-DITRA-HEAT-E-HK-SK Splice Kit is to repair damaged Schluter®-DITRA-HEAT-E-HK heating cables to operable condition. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-HK-SK system throughout Wildwood, The Villages, and Central Florida.

DITRA-HEAT-E-R is a non-programmable digital thermostat used to control the DITRA-HEAT-E-HK heating cables (either 120 V or 240 V).The thermostat features a built in Class A ground fault circuit interrupter (GFCI) with indicator light and includes a floor temperature sensor. DITRA-HEAT-E-R is operated via a simple on/off switch. Two heating cables may be connected to the thermostat, up to the total heating load limit of 15 amps. The DITRA-HEAT-E-RR power module may be used in conjunction with the thermostat when the heating load exceeds 15 amps (e.g., in large floor applications) to maintain a single point of control. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-R system throughout Wildwood, The Villages, and Central Florida.

The power module may be used in conjunction with the DITRA-HEAT-E-WIFI, DITRA-HEAT-E-RT, or DITRA-HEAT-E-R thermostats when the heating load exceeds 15 amps (e.g., in large floor applications) to maintain a single point of control. Up to 16 DITRA-HEAT-E-RR power modules may be connected in series via low voltage signal wire to a single DITRA-HEAT-E-WIFI, DITRA-HEAT-E-RT, or DITRA-HEAT-E-R thermostat. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-RR system throughout Wildwood, The Villages, and Central Florida.

Schluter®-DITRA-HEAT-E-RRS is a power module that extends power output when used in conjunction with the DITRA-HEAT-E-RS1 thermostat. The DITRA-HEAT-E-RRS power module can only be used in conjunction with the DITRA-HEAT-E-RS1 thermostats. The power module is used when the heating load exceeds 15 amps (e.g., in large floor applications) to maintain a single point of control. No more than 10 DITRA-HEAT-E-RRS power modules should be connected in a series to a single DITRA-HEAT-E-RS1 thermostat; however, that number may decrease depending on the application. The goal is to eliminate any uneven temperatures in a large room which may present various heat loss characteristics (e.g., a below grade application with 1 thermostat and 3 power modules can cover over 1100 square feet. The initial temperature from one end of the application to the other may vary). LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-RRS system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-DITRA-HEAT-E-RS1 is a smart thermostat for the Schluter®-DITRA-HEAT floor warming system. It features a sleek design with a mirror-finish and third-party integration with popular voice and home assistants to easily include floor warming into your smart home capabilities. DITRA-HEAT-E-RS1 is a smart thermostat used to control the DITRA-HEAT-E-HK heating cables (either 120 V or 240 V). The thermostat features a built-in Class A ground fault circuit interrupter (GFCI) and includes input terminals to connect a 10k floor temperature sensor. Two floor temperature sensors are provided with each DITRA-HEAT-E-HK heating cable box. The DITRA-HEAT-E-RS1 was designed to be mainly operated via the Schluter Smart Thermostat app. All features can be programmed and controlled using the app, and these features include remote access, time-temperature scheduling, maximum and minimum floor temperatures, maximum ambient temperature when in floor control mode, easy smart home integration, geofencing capabilities, etc. The basic installation setup can be programmed from the thermostat menu using the dot soft button and the arrows. Manual temperature adjustments can be made directly using the arrows. When connected to Wi-Fi, the thermostat provides convenient monitoring and adjustment of the floor warming system via our mobile app. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-RS1 system throughout Wildwood, The Villages, and Central Florida.

DITRA-HEAT-E-RT is a programmable touchscreen thermostat used to control the DITRA-HEAT-E-HK heating cables (either 120 V or 240 V). The thermostat features a 5 mA built-in ground fault circuit interrupter (GFCI) with indicator light. DITRA-HEAT-E-RT is operated via LCD touchscreen controls and features a pre-set schedule for convenience, which may be programmed to fit any schedule. Two heating cables may be connected to the thermostat, up to the total heating load limit of 15 amps. The DITRA-HEAT-E-RR power module may be used in conjunction with the thermostat when the heating load exceeds 15 amps (e.g., in large floor applications) to maintain a single point of control. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-RT system throughout Wildwood, The Villages, and Central Florida.

DITRA-HEAT-E-WiFi is a programmable WiFi touchscreen thermostat used to control the DITRA-HEAT-E-HK heating cables (either 120 V or 240 V). The thermostat features a built-in Class A ground fault circuit interrupter (GFCI). DITRA-HEAT-E-WiFi is operated via LCD touchscreen controls and features a pre-set schedule for convenience, which may be programmed to fit any schedule. When connected to WiFi, the thermostat provides convenient monitoring and adjustment of the floor warming system via the web or mobile app. Two heating cables may be connected to the thermostat, up to the total heating load limit of 15 amps. The DITRA-HEAT-E-RR power module may be used in conjunction with the thermostat when the heating load exceeds 15 amps (e.g., in large floor applications) to maintain a single point of control. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-E-WiFi system throughout Wildwood, The Villages, and Central Florida.

DITRA-HEAT-PS peel and stick membrane features a pressure-sensitive adhesive (PSA) to bond the membrane to the substrate, replacing the need for thin-set mortar. The peel and stick versions integrate customizable, comfortable electric floor warming with the same core functions of DITRA-HEAT: uncoupling, waterproofing, vapor management, and support. Note: The DITRA-HEAT-PS membrane does not comply with the requirements specified in ANSI A118.10 – American National Standard Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation. For applications requiring membrane compliance with or certification to the ANSI A118.10, select the DITRA-HEAT membrane that is installed with thin-set mortar. Alternatively, the DITRA-HEAT-PS membrane may be covered with the Schluter(R)-KERDI membrane, which is certified to meet ANSI A118.10. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-HEAT-PS system throughout Wildwood, The Villages, and Central Florida.

DITRA-PS is a peel and stick membrane that features a pressure sensitive adhesive (PSA) to bond the membrane to the substrate, replacing the need for thin-set mortar. The -PS version offers the same core functions as DITRA. LA Flooring is a certified Schluter installer, providing professional installation of the DITRA-PS system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI is a pliable, sheet-applied, bonded waterproof membrane and vapor retarder with limited crack-bridging capabilities. KERDI features a modified polyethylene (PEVA) core with non-woven polypropylene on both sides to anchor the membrane in the thin-set mortar. KERDI was developed as a waterproofing membrane to be used in conjunction with ceramic and stone tile coverings. Tiles can be installed directly on KERDI using the thin-bed method. Other trowel-applied covering materials, such as plaster, can also be used. KERDI has been evaluated according to the “Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers, Version 1.1” for California Specification 01350 and found to comply with the VOC requirements. California Specification 01350 is referenced by various green building standards and rating systems. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI system throughout Wildwood, The Villages, and Central Florida.

Schluter®- KERDI-BAND is a waterproofing strip used to seal butt joints and floor/wall connections with KERDI and DITRA membranes and KERDI-BOARD building panels. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BAND system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD is a multifunctional tile substrate and building panel, which can also be used for creating bonded waterproofing assemblies with tile coverings. It consists of an extruded polystyrene foam panel, with a special reinforcement material on both sides and fleece webbing for effective anchoring in thin-set mortar.KERDI-BOARD can be used in a multitude of interior applications. KERDI-BOARD is not intended for exterior applications. With the available panel thicknesses of 3/16", 3/8", 1/2", 5/8", 3/4", 1", 1-1/2", and 2" (5, 9, 12.5, 15, 19, 25, 38, and 50 mm), KERDI-BOARD allows the installer to prepare and create a broad range of substrates and building elements for the installation of ceramic and natural stone tile that are flat, level, plumb, square, and dimensionally stable. With suitable preparation of the abutting seams and joint areas, the panel may be used for bonded waterproofing assemblies. The boards are simply cut to size with a utility knife. The gridlines, which are printed on the surface, are helpful for neat and quick cuts and installation. Tiles can be installed directly over KERDI-BOARD using the thin-set method. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-E is an L-shaped panel used to create corners and pipe or column coverings. The panels feature a V-shaped groove and are shipped in a space-saving flat design, which makes them easy to store. The flat panels are also quick to cut to the necessary dimensions. Thin-set mortar, Schluter®-KERDI-FIX adhesive, or double-sided adhesive tape is applied to the V-groove. The panels are then folded prior to installation. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-E system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-KERDI-BOARD-KIT combines all of the necessary components to waterproof and tile ready the walls of your bathtub and acrylic shower base using waterproof building panels. The KERDI-BOARD-KIT provides enough KERDI-BOARD to cover up to 101 ft² (9.4 m²) of wall area. For example, in installations with standard 8 ft. ceilings, the panels included will cover 12 linear feet (3.6 m). Notes: LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-KIT system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-SB is a prefabricated shower bench, made of KERDI-BOARD, for use in conjunction with the Schluter®-Shower System. KERDI-SHOWER-SB is waterproof and ready for tile, leaving only sealing of joints and corners to complete waterproofing. The bench is available in triangular and rectangular configurations in the following sizes (width x depth x height). The triangular benches are 16" x 16” x 20” (41 x 41 x 51 cm) and 24” x 24” x 20” (61 x 61 x 51 cm). The rectangular benches are 38” x 11-½” x 20” (97 x 29 x 51 cm) and 48” x 16” x 20” (122 x 41 x 51 cm). LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-SB system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-SC is a prefabricated shower curb, made of KERDI-BOARD, for use in conjunction with the Schluter®-Shower System. KERDI-SHOWER-SC is waterproof and ready for tile, leaving only sealing of joints and corners to complete waterproofing. The curb can be used in conjunction with KERDI-SHOWER-T/-TS/-TT shower trays or mortar bases and is available in three sizes, 38" x 6" x 4-1/2" (97 x 15 x 11.5 cm), 48" x 6" x 4-1/2" (122 x 15 x 11.5 cm) and 60” x 6” x 4-1/2” (152 cm x 15 cm x 11.5 cm). LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-SC system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-SN is a prefabricated shower niche made of KERDI-BOARD that can be installed in both KERDI and KERDI-BOARD wall assemblies. The shower niche features a 1/2" (12.5 mm) -thick by 2" (50 mm) -wide integrated bonding flange and is available in 12" x 6" (30 x 15 cm), 12" x 12" (30 x 30 cm), 12" x 20" (30 x 51 cm), and 12" x 28" (30 x 71 cm) sizes.All niches include screws and washers with the kits and a pre-cut KERDI-BAND frame for waterproofing the transition of the niche to the adjacent wall. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-SN system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-SNLT is a prefabricated shower niche made of KERDI-BOARD that incorporates a mounting profile with a diffused LED light strip. It features a pre-installed waterproof connection box to ensure the electrical connection is code-compliant. The KERDI-BOARD-SNLT niche can be installed in both KERDI and KERDI-BOARD wall assemblies. The shower niche features a 1/2" (12.5 mm) thick by 2" (50 mm) wide integrated bonding flange and is available in various sizes, with options for vertical or horizontal installation. The mounting profile is made of anodized aluminum with satin finish (AE). It is sized to fit along the top of the niche and features a cut out designed to pass the cable. The LED light strip is encased in a silicone tube that provides an evenly diffused line of warm white light measuring 3000K and nests into the mounting profile. Each niche kit niche includes: LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-SNLT system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-U is a U-shaped panel used to create pipe or column coverings. The panels feature V-shaped grooves and are shipped in a space-saving flat design, which makes them easy to store. The flat panels are also quick to cut to the necessary dimensions. Thin-set mortar, Schluter®-KERDI-FIX adhesive, or double-sided adhesive tape is applied to the V-grooves. The panels are then folded prior to installation. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-U system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-V is a vertically grooved substrate and building panel for creating curved elements. If a larger expanse of panels is required, several panels can be connected along the edges with thin-set mortar, Schluter®-KERDI-FIX adhesive, or double-sided adhesive tape. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-V system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZA is a brushed stainless steel, U-shaped profile with two perforated anchoring legs. It is used to finish visible edges of partition walls and shelves. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZA system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZB is a stainless steel, U-shaped profile with three-sided perforation. It is used to fasten and stabilize partition walls and other structures made of KERDI-BOARD panels. The surfaces of the profile are hidden by the tile covering. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZB system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZC is a brushed stainless steel, U-shaped profile with one perforated anchoring leg. It is used to finish the edges of countertops, vanities, and similar structures in conjunction with the Schluter®-RONDEC or Schluter®-QUADEC finishing profiles. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZC system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZDK is a double-sided adhesive tape used to attach KERDI-BOARD panels in joint areas or similar. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZDK system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZFP is a flat plastic profile, which is adhered behind the KERDI-BOARD-ZA U-shaped profile to improve fastening of hardware with screws. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZFP system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZT are galvanized steel washers used to fasten KERDI-BOARD to metal or wood stud framing. They feature tabs that penetrate the surface of the KERDI-BOARD and temporarily hold the washers in place to enable quick installation of the corresponding screws. KERDI-BOARD-ZS are coarse thread screws used to fasten KERDI-BOARD to wood stud framing with the corresponding washers. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZS/-ZT system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZSA is an adhesive tape for reinforcing the joint areas of KERDI-BOARD panels. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZSA system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZSD are anchors used to provide additional mechanical attachment of KERDI-BOARD when the bond between the thin-set mortar and the substrate is questionable. Appropriate drill bit size: 8 mm - 5/16" . Drill hole 10 mm - 3/8" deeper than anchor length. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZSD system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-BOARD-ZW is a stainless steel angle profile with two trapezoid perforated anchoring legs. It is used to fasten and stabilize structures made of KERDI-BOARD panels. It is attached to the substrate with either screws or thin-set mortar. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-BOARD-ZW system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-DRAIN is a shower drain specifically designed to allow connections to KERDI or other load-bearing, bonded waterproof membranes. The membrane is adhered to the large integrated bonding flange to form a waterproof connection at the top of the drain assembly. KERDI-DRAIN consists of a drain body and fully adjustable grate assembly or covering support to which tile is applied. The grate assembly accommodates a wide range of tile thicknesses and allows lateral and tilt adjustment as well. The covering support is placed flush with the top of the bonding flange and can therefore accommodate any thickness tile covering. The standard KERDI-DRAIN is attached directly to the waste line. The drain body is available in ABS, PVC, or stainless steel. The plastic drain bodies feature a fleece-covered bonding flange. They are available with standard 2" (50 mm) and 3" (75 mm) outlets and attached to the pipe using an appropriate solvent cement. The stainless steel drain bodies are available with standard 2" (50 mm) or 3" (75 mm) no-hub outlets or 2" (50 mm) threaded outlet. The no-hub outlets are attached to the pipe using an appropriate mechanical (e.g., flexible or no-hub) coupling. The threaded outlets are attached to the pipe using thread sealing compound or tape. The simple connection to standard drain outlets makes KERDI-DRAIN suitable for new construction and renovation. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-DRAIN system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-KERDI-DRAIN-A adaptor kits are designed to convert clamping ring drains to integrated bonding flange drains when removal of the clamping ring drain is not practical (e.g., when they are set in concrete slabs). The adaptor kit includes a steel adaptor ring, available in 5-1/2" (139.7 mm) and 7-1/2" (191 mm) diameter sizes, with an over-molded rubber gasket and a variety of perforated hole patterns that align with most common clamping ring drains. The adaptor ring replaces the clamping ring and is attached to the existing drain body using the clamping ring bolts. This connection is made watertight via the rubber gasket and Schluter®-KERDI-FIX adhesive/sealant. The adaptor drain with integrated bonding flange slides into the adaptor ring with the over-molded rubber gasket ensuring a watertight seal. Adaptor kits are suitable for both mortar beds and KERDI-SHOWER-T/-TS/-TT shower tray applications. Grate assemblies consist of a frame, which can be seamlessly adjusted to the thickness and layout of the ceramic tile or stone covering via the height adjustment collar and lateral adjustment ring and grates or cleanout covers that are placed within the frame. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-DRAIN-A system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-DRAIN-F is a floor drain specifically designed to allow connections to Schluter®-DITRA, DITRA-XL, DITRA-HEAT, and DITRA-HEAT-DUO uncoupling membranes. KERDI-DRAIN-F consists of a drain body and adjustable grate assembly that accommodates a wide range of tile thicknesses. The drain body is available in polypropylene or stainless steel, each with a laminated Schluter®-KERDI collar that ensures a simple connection to the uncoupling membrane on the floor and at wall transitions. The polypropylene drain features a 2" (50 mm) NPT outlet and is supplied with PVC and ABS couplings for simple attachment to the pipe using an appropriate solvent cement. The stainless steel drains are available with standard 2" (50 mm) no-hub and threaded outlets. The no-hub outlets are attached to the pipe using an appropriate mechanical (e.g., flexible or no-hub) coupling. The threaded outlets are attached to the pipe using thread sealing tape or compound. The simple connection to standard drain outlets makes KERDI-DRAIN-F suitable for new construction and renovation/remodeling projects. The KERDI-DRAIN-F grate assembly consists of a frame, which can be seamlessly adjusted to the thickness of the ceramic tile or stone covering via the vertical height adjustment collar and grates that are placed within the frame. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-DRAIN-F system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-DRAIN-H is a shower drain with an integrated bonding flange that provides a large contact area for a secure connection to Schluter®-KERDI waterproof membrane at the top of the assembly. KERDI-DRAIN-H is appropriate for both mortar bed and Schluter®- KERDI-SHOWER-T/-TS/-TT shower tray applications. The bonding flange is sloped to simplify installation of the mortar bed. KERDI-DRAIN-H provides a horizontal connection to the drain pipe and is available in ABS or PVC with a 2" (50 mm) outlet. It is ideal for applications where the use of a vertical connection to the drain pipe is not possible or practical (e.g., suspended or post-tension concrete floors, basement slabs, or wood floor installations where relocating the hole in the floor is not practical). The horizontal outlet allows the positioning of the drain in the desired area regardless of drain pipe location. A compensation board, Schluter®-KERDI-SHOWER-CB is available for use with KERDI-DRAIN-H in conjunction the KERDI-SHOWER-T/-TS/-TT shower trays. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-DRAIN-H system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-DS is a bonded waterproof membrane and vapor retarder with very low water vapor permeance for use in continuous use steam rooms and similar applications. KERDI-DS has been evaluated according to the “Standard Method for the Testing and Evaluation of Volatile Organic Chemical Emissions from Indoor Sources Using Environmental Chambers, Version 1.1” for California Specification 01350 and found to comply with the VOC requirements. California Specification 01350 is referenced by various green building standards and rating systems. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-DS system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-FIX is a single component, waterproof sealing and bonding compound with a silane-modified polymer base. KERDI-FIX can be used to waterproof pipe and valve protrusions in the Schluter®- Shower System in conjunction with the Schluter®-KERDI membrane and Schluter®- KERDI-BOARD. KERDI-FIX is required to bond the KERDI membrane to the stainless steel Schluter®-KERDI-DRAIN bonding flange and can be used to bond KERDI to building elements such as bathtubs, window elements, and door frames. KERDI-BOARD can be adhered with KERDI-FIX in various applications, such as countertops, partitions, and other building elements. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-FIX system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-FLEX is a flexible polyethylene waterproofing strip used to seal movement joints over Schluter®-DITRA in specialty applications where large movements are expected, i.e. over expansion joints or construction joints. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-FLEX system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-KERECK/-KERS-B are preformed, seamless corners made for waterproofing inside and outside corners of KERDI, KERDI-BOARD, and DITRA assemblies to prevent leaks and mold-growth. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-KERECK-F/-KERS-B system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-KERS are preformed, seamless corners made of Schluter®-KERDI for waterproofing floor/wall/shower base connections in curbless shower applications where the Schluter®-KERDI-LINE linear drain is installed adjacent to the wall. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-KERS system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-KM prefabricated seal is cut sections of the Schluter®-KERDI waterproofing membrane designed to seal protrusions through the KERDI or Schluter®-DITRA/DITRA-XL membranes. KERDI-KM is designed to be used in conjunction with Schluter®-KERDI-FIX or equivalent sealant to seal around pipes or other similar elements. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-KM system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-LINE is a low profile linear shower drain specifically designed for bonded waterproofing assemblies. KERDI-LINE can be installed adjacent to walls or at intermediate locations. The floor can be sloped on a single plane to KERDI-LINE, which enables the use of large-format tiles and creates interesting design opportunities. KERDI-LINE consists of a formed stainless steel channel body and grate assembly or covering support to which tile is applied. The channel body features a standard 2" (50 mm) no-hub outlet and is attached to the pipe using an appropriate mechanical (e.g., flexible or no-hub) coupling. The simple connection to standard drain outlets makes KERDI-LINE suitable for new construction and renovation. KERDI-LINE is available with both center and off-set outlets. The off-set outlet is located 8" (20.3 cm) from the edge of the channel body and provides flexibility when obstacles (e.g., floor joists) are encountered during installation. KERDI-LINE includes a corresponding polystyrene foam channel support to set the drain elevation to the corresponding KERDI-SHOWER-LT/-LTS shower trays. The perimeter of the channel body consists of a bonding flange laminated with a collar made of KERDI. It ensures a simple and secure connection to the bonded waterproofing assembly, both in the floor area and on adjacent walls. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-LINE system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-KERDI-LINE-A adaptor kits are designed to convert clamping ring drains to the KERDI-LINE channel body when removal of the clamping ring drain is not practical (e.g., when they are set in concrete slabs). The adaptor kit includes a steel adaptor ring, available in 5-1/2" (139.7 mm) diameter, with an over-molded rubber gasket and a variety of perforated hole patterns that align with most common clamping ring drains. The adaptor ring replaces the clamping ring and is attached to the existing drain body using the clamping ring bolts. This connection is made watertight via the rubber gasket and Schluter®-KERDI-FIX adhesive/sealant. The KERDI-LINE channel body slides into the adaptor ring with the over-molded rubber gasket ensuring a watertight seal. Adaptor kits are suitable for both mortar beds and KERDI-SHOWER-LT/-LTS shower tray applications. The KERDI-LINE grate assembly consists of a steel frame that can be seamlessly adjusted to the thickness of the ceramic tile or stone covering – 1/8" to 1" (3 mm to 25 mm) for standard grate assemblies and 1/4" to 23/32" (6 mm to 18 mm) for KERDI-LINE-STYLE grate assemblies – and stainless steel grates that are placed within the frame. The standard grate assembly frame features a 3/8" (10 mm) wide reveal after installation and can be combined with one of two grate options: SOLID (A) or SQUARE (B). LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-LINE-A system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-LINE-VARIO is a low-profile, variable length linear shower drain specifically designed for bonded waterproofing assemblies. KERDI-LINE-VARIO can be initially cut to size on-site to fit the specific dimensions of the shower. The floor can be sloped on a single plane to KERDI-LINE-VARIO, which enables the use of large format tiles and creates interesting design opportunities. KERDI-LINE-VARIO is best suited for placement against the wall but can also be installed in the center of the shower. For drain placement at the entrance of the shower, please refer to the KERDI-LINE linear drain. KERDI-LINE-VARIO consists of a polypropylene flange, a formed stainless steel channel, a stainless steel grate, and stainless steel end caps for applications involving trimmed lengths. The KERDI-LINE-VARIO flange comprises an injection molded polypropylene drain body featuring a standard 2" (50 mm) NPT outlet, which attaches to a standard, threaded, mechanical coupling to allow for an adhesive chemical bond to the drainpipe. KERDI-LINE-VARIO is supplied with PVC and ABS couplings. The simple connection makes KERDI-LINE-VARIO suitable for new construction and renovations. The perimeter of the polypropylene flange consists of a bonding flange laminated with a collar made of KERDI. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-LINE-VARIO system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-SEAL-PS and Schluter®-KERDI-SEAL-MV are prefabricated sections of KERDI with over molded rubber gaskets that are used to seal pipe protrusions through the KERDI waterproofing membrane (e.g. at showerheads and tub spouts) and protect moisture-sensitive backing panels at the mixing valve. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SEAL-PS/-MV system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-SHOWER-CB is a compensation board available for use with KERDI-DRAIN-H, KERDI-DRAIN-A, and KERDI-LINE-A in conjunction with KERDI-SHOWER prefabricated shower trays. It allows for the shower trays to be installed in instances when they are unable to be installed directly on the subfloor without interfering with other components. KERDI-SHOWER-CB is made of lightweight, expanded polystyrene for constructing mortar-free shower bases. It is available in 1″ (2.5 cm) and 3-1/2″ (8.9 cm) perimeter height, both offered as 48″ x 24″ (122 cm x 61 cm) sheets. The compensation board can be easily cut to size and fit around the drain components and multiple boards can be used to fit the size and shape of the shower. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SHOWER-CB system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-KERDI-SHOWER-KIT contains all of the waterproofing components, including the shower tray and shower curb, required to create a maintenance-free, watertight shower assembly without a mortar bed. KERDI-DRAIN grate and flange must be ordered separately. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SHOWER-KIT system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-KERDI-SHOWER-KIT-FL contains all of the waterproofing components, including the shower tray and shower curb, required to create a maintenance-free, watertight shower assembly without a mortar bed. Drain grate must be ordered separately. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SHOWER-KIT-FL system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-KERDI-SHOWER-KIT is an all-inclusive package containing each of the integrated family of components required to create a maintenance-free, watertight shower assembly without a mortar bed. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SHOWER-KIT-FLG system throughout Wildwood, The Villages, and Central Florida.

Schluter®-KERDI-SHOWER-LT/-LTS are prefabricated expanded polystyrene sloped trays with integrated KERDI waterproofing specifically designed to accept the KERDI-LINE linear drain. The trays are available in 39" x 39" (100 cm x 100 cm), 55" x 55" (140 cm x 140 cm), 48” x 48” (122 cm x 122 cm), 36” x 72” (91 cm x 183 cm), 38” x 76” (97 cm x 193 cm) and 36” x 55” (91 cm x 140 cm) sizes. The KERDI-SHOWER-LT/-LTS are available with center (-LT) and perimeter (-LTS) drain placements in ten configurations with reduced perimeter heights to aide in the installation of curbless showers. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SHOWER-LT/-LTS system throughout Wildwood, The Villages, and Central Florida.

Schluter ®-KERDI-SHOWER-R is a lightweight, expanded polystyrene shower ramp with integrated Schluter®-KERDI waterproofing, designed to facilitate the construction of access ramps for tiled showers. The ramp integrates with the Schluter® -Shower System to create accessible, curbless showers and adheres to the ADA’s slope ratio. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SHOWER-R system throughout Wildwood, The Villages, and Central Florida.

The trays are made of lightweight, expanded polystyrene for constructing mortar-free shower bases. Each of these sloped, prefabricated shower trays are designed to integrate with the Schluter®-KERDI-DRAIN. The KERDI-SHOWER-T is the standard tray and are available with center drain placement is available in 38" x 60" (97 x 152 cm), 48" x 60" (122 x 152 cm), 48" x 72" (122 x 183 cm), 60" x 60" (152 x 152 cm) and 72" x 72" (183 x 183 cm) sizes. The KERDI-SHOWER-TS with an off-center drain placement is available in 38" x 60" (97 x 152 cm), for bathtub replacements. KERDI-SHOWER-TT features a thin perimeter height that simplifies curbless shower construction and is available in 36” x 36” (91 x 91 cm), 32" x 38" (81 x 97 cm), 38” x 38” (97 x 97 cm), 36" x 48" (91 x 122 cm) and 48” x 48” (122 x 122 cm) sizes. The KERDI-SHOWER-TT is also available in a neo angle configuration in 38” x 38” (97 x 97 cm). The neo-angle tray features an off-center drain placement: 12” (30.5 cm) from the 38” sides of the tray. LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-SHOWER-T/-TS/-TT system throughout Wildwood, The Villages, and Central Florida.

The Schluter®-KERDI-TUBKIT contains all the components necessary to create a fully waterproof and vapor tight bathtub surround assembly LA Flooring is a certified Schluter installer, providing professional installation of the KERDI-TUBKIT system throughout Wildwood, The Villages, and Central Florida.

Schluter®-LIPROTEC-CW connection cables are rated for in-wall installation - no conduit required. The cable features a pre-installed waterproof snap-in gland for a secure connection to the top of the niche, and connectors to attach to the LED strip. LA Flooring is a certified Schluter installer, providing professional installation of the LIPROTEC-CW system throughout Wildwood, The Villages, and Central Florida.

Schluter®-LIPROTEC-ECD is an in-line dimmable driver that is hard wired into your electrical. It is compatible with a range of popular dimmer switches, allowing you to have matching light switches throughout your bathroom. The available dimming range is 5% to 100% and can control multiple KERDI-BOARD-SNLT niches (up to 24 watts). The LIPROTEC-ECD includes a metal enclosure and must be installed in an accessible location, such as a closet or vanity. LA Flooring is a certified Schluter installer, providing professional installation of the LIPROTEC-ECD system throughout Wildwood, The Villages, and Central Florida.

Schluter®-LIPROTEC-ECX is an all-in-one LED power supply and in-wall dimmer switch. It offers smooth, even dimming with a dimming range of 5% to 100%. LIPROTEC-ECX can control multiple KERDI-BOARD-SNLT niches (up to 60 watts). Additionally, it includes three interchangeable face plates to match most decors. LA Flooring is a certified Schluter installer, providing professional installation of the LIPROTEC-ECX system throughout Wildwood, The Villages, and Central Florida.

Schluter®-REFLEECE is a fleece made of recycled PET with an adhesive coating on the back. It is suitable for the application of temporary, removable tile and natural stone coverings in the floor area. REFLECE features a self-adhesive backside that can be easily removed from the subfloor during deconstruction and does not cause any damage to the existing subfloor. REFLEECE is a 1/32" (0.85 mm) thick non-woven fabric made of PET (polyethylene terephthalate), with a special solvent-free and plasticizer-free adhesive coating on the back. Note: There is no release film on the back of the product. The adhesive is not UV-stable in the long term, therefore permanent and intensive sunlight should be avoided during storage. REFLEECE can be stored for at least 18 months if kept dry and frost-free 41-86 °F (5-30°C). Impact Sound Insulation Schluter®-REFLEECE overlaid with 5/16"-thick porcelain tile received a rating of ΔIIC 17 when tested according to test method ASTM E2179. The actual degree of improvement of the respective assembly depends on the local conditions (structural design) and can deviate from this value. Therefore, the determined test values cannot be transferred to every construction site situation. LA Flooring is a certified Schluter installer, providing professional installation of the REFLEECE system throughout Wildwood, The Villages, and Central Florida.

Schluter®-RENO-RAMP is designed to provide a smooth transition between tile coverings and floor coverings at lower elevations or finished concrete, particularly in commercial applications where wheel carts are used (e.g., bakeries, hospitals, etc.). The profile is available in anodized aluminum. RENO-RAMP features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a sloped transition surface that terminates at the height of the tile edge. The profile protects tile edges and provides a sloped surface to eliminate trip hazards and allow easy access for wheel carts. RENO-RAMP features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. Schluter®-RENO-RAMP-K is a variant of the profile without an anchoring leg. Note: When using Schluter® uncoupling membranes with RENO-RAMP profiles, factor in the thickness of the membrane over the anchoring leg when selecting the profile height. RENO-RAMP-K is installed adjacent to existing floor coverings, e.g., retrofitting between existing floor coverings and bare concrete without having to disturb the existing flooring. All sizes of RENO-RAMP, except sizes 9/16" (15 mm) and 3/4" (20 mm), are compliant with the Americans with Disabilities Act (ADA). LA Flooring is a certified Schluter installer, providing professional installation of the RENO-RAMP/-K system throughout Wildwood, The Villages, and Central Florida.

Schluter®-RENO-T is designed to provide transitions between existing same-height, hard-surface floor coverings (e.g., ceramic tile or natural stone, parquet flooring, concrete pavers, laminate, etc.), primarily in retrofit applications. The profile is available in stainless steel, solid brass, and anodized aluminum. RENO-T is installed within the existing joint cavity and overlaps adjoining surface materials, thus preventing edges from becoming damaged when subjected to mechanical stress. RENO-T, in brass and anodized aluminum size 9/14, is flexible in the lateral direction and can be used in curved applications. LA Flooring is a certified Schluter installer, providing professional installation of the RENO-T system throughout Wildwood, The Villages, and Central Florida.

Schluter®-RENO-TK is designed to provide a smooth transition from tile coverings to floor coverings at lower elevations, typically carpet. The profile is available in stainless steel, solid brass, and anodized aluminum. RENO-TK features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a sloped surface to eliminate trip hazards and protect tile edges. The 1/4" (6 mm) channel beneath the sloped flange of the profile hides and protects the cut edge of lower adjoining surface coverings. All sizes of the RENO-TK are compliant with the Americans with Disabilities Act (ADA). RENO-TK, in anodized aluminum, features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. The anchoring leg of RENO-TK, in solid brass and anodized aluminum, sizes 60 to 100, is available with a special radius perforation “R” so that the profile can be used to form curves. LA Flooring is a certified Schluter installer, providing professional installation of the RENO-TK system throughout Wildwood, The Villages, and Central Florida.

Schluter®-RENO-U is designed to provide a smooth transition between tile coverings and floor coverings at lower elevations or finished concrete. The profile is available in stainless steel, solid brass and anodized aluminum. RENO-U features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a sloped surface (approximately 25°) that eliminates trip hazards and protects tile edges. The leading edge of the profile abuts the lower surface covering, typically VCT. RENO-U, in aluminum, features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. In installations where the leading edge abuts a lower surface covering, all sizes of RENO-U, except the 3/4" (20 mm) and 11/16" (17.5 mm), are compliant with the Americans with Disabilities Act (ADA). In installations where the leading edge rests on top of the lower floor covering (e.g., finished concrete), the 3/4" (20 mm), 11/16" (17.5 mm), and 9/16" (15 mm) sizes are not ADA-compliant. Note: When using Schluter® uncoupling membranes with RENO-U profiles, factor in the thickness of the membrane over the anchoring leg when selecting the profile height. LA Flooring is a certified Schluter installer, providing professional installation of the RENO-U system throughout Wildwood, The Villages, and Central Florida.

Schluter®-RENO-V is designed to provide a smooth transition between tile coverings and floor coverings at lower elevations. The profile is available in anodized aluminum. RENO-V features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and a movable transition arm that allows the profile to adjust to the height of the adjacent floor covering via a ball and socket joint. The profile protects tile edges and provides a sloped surface to eliminate trip hazards. RENO-V features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. RENO-V is also suitable for heavy-duty applications (e.g., entrances to garages or loading docks). In such cases, the adjustable arm is backfilled with mortar. LA Flooring is a certified Schluter installer, providing professional installation of the RENO-V system throughout Wildwood, The Villages, and Central Florida.

Schluter®-SCHIENE is designed to provide edging for tile coverings. Typical applications include edge protection where tile is bordered by carpet, at expansion joints, or as a decorative edging for stairs. SCHIENE is available in stainless steel, solid brass, aluminum and anodized aluminum. SCHIENE is also available in textured color-coated aluminum finishes, which are suitable for floor installations within residential applications only. The profile features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and an 87° sloped vertical wall section that transfers point loads to the substrate and surface covering while protecting tile edges from damage. SCHIENE, in solid brass, aluminum, textured color-coated aluminum, and anodized aluminum, features a 5° sloped top flange and fillet at the anchoring leg/vertical section interface to enhance edge protection by reducing stresses on the tile, and, in sizes greater than 1/4" (6 mm), features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. The anchoring leg of SCHIENE, in all materials, is available with a special radius perforation “R” so that the profile can be used to form curves. LA Flooring is a certified Schluter installer, providing professional installation of the SCHIENE system throughout Wildwood, The Villages, and Central Florida.

Schluter®-VINPRO™-S is designed to provide edging for resilient surface coverings (e.g. LVT). Typical applications include edge protection where the resilient covering is bordered by carpet, floor coverings of similar heights, or as a finishing edge to wall skirting applications. The profile is available in anodized aluminum. VINPRO-S features a tapered anchoring leg, with unique holes spaced evenly along the length of the profile for use with fasteners. LA Flooring is a certified Schluter installer, providing professional installation of the VINPRO-S system throughout Wildwood, The Villages, and Central Florida.

Schluter-VINPRO-T is designed to provide transitions between existing same-height, resilient floor coverings, in new and retrofit applications (e.g. LVT). VINPRO-T is installed within the joint cavity and overlaps adjoining surface materials, thus preventing edges from becoming damaged when subjected to mechanical stress. LA Flooring is a certified Schluter installer, providing professional installation of the VINPRO-T system throughout Wildwood, The Villages, and Central Florida.

Schluter-VINPRO-U is designed to provide a smooth transition between resilient floor coverings (e.g. LVT) and floor coverings at lower elevations or finished concrete. The profile is available in anodized aluminum. VINPRO-U features a tapered anchoring leg, with unique holes spaced evenly along the length of the profile for use with fasteners. The anchoring leg can also be bonded to the substrate using adhesive such as Schluter®-KERDI-FIX. The profile features a 1/4" (6 mm) or 3/8" (10 mm) wide sloped top flange to hide the cut edge of the resilient floor covering, providing a finished look. LA Flooring is a certified Schluter installer, providing professional installation of the VINPRO-U system throughout Wildwood, The Villages, and Central Florida.